plummer block bearing size chart pdf

The bearings are either directly seated on the shaft or fixed with adapter sleeves. This results in different shaft diameters for the same bearing size.

housing units. Further information. □ Catalogue GK 1, Bearing Housings https://www.schaeffler.de/std/1F7F.

Plummer Blocks Interchange Section 56 Plummer Block Housings for Tapered Bore Bearings 60 Cap & Fixing Bolts Sizes Recommended Tightening Torques SNN Housing Cap Bolt Size Grade 8.8

Plummer Blocks Plummer Blocks G-4 G-5 Size of castings (mm) Unit: mm 120 or below 121 to 250 251 to 400 401 to 800 801 to 1600 ±1.5 ±2.0 ±3.0 ±4.0 ±6.0 A plummer block number

The SN Housing will accept the self-aligning ball or spherical roller bearings with adapter sleeves. The SN is designed according to. DIN 736. Each size is 

Permanently Lubricated WashdownMounted Ball Bearings with Two-Bolt Flange. Permanently lubricated and IP69K certified for washdown environments, these mounted ball bearings are useful for hard-to-reach areas in food, beverage, pharmaceutical, and chemical plants. Mount them using their two-bolt flange.

4 Nominal number of plummer block and bearing 2.2 Nominal number of rolling bearing Rolling bearing part numbers indicate bearing type, dimensions, tolerances, internal construction,

of bearings and accessories to extend bearing life inee uime n eue minenne . O ue u n inene eiin u i timken ue uni eue u l le n eneline imenin e eine nm inu n. timken® ue uni ele u en in mellu

Plummer Blocks These consist of self-alighning ball bearings or spherical roller bearings and a housing in which the bearings are installed. The housing varies in shape. Having a large load carrying capacity and being easy to handle they are used in wide variety of industrial machines. 166 www.dpibearings.com www.dpibearings.com 167

FAG supplies split plummer block housings of series SNV for shafts with di- ameters from 20 to 160 mm and for 3/ 4to 51/ 2inches. The numbers in the housing codes in- dicate the housing bore and therefore the outside diameter of the suitable bearing e.g. 100 mm in the case of SNV100.

Plummer Blocks Plummer Blocks G-6 G-7 All types All sizes Plummer block nominal dimension Surface finish roughness 5 12.5Ra Machining allowance L-L Unit: mm Tolerance 31 to 120 ±0.8 121 to 315 ±1.2 316 to 1 000 ±2.0 1 001 to 2 000 ±3.0 Dimension after machining L Table 3 Machining allowance Unit: mm Table 4 Tolerance of dimension L' after

PDF. When selecting a Plummer block housing, many factors should be considered. The selection process depends not only on the bearing type and size but also on the housing’s ability to safely accommodate the magnitude and characteristics of all applied loads. Besides this, important considerations are mounting, maintenance, sealing options

Pillow blocks cast housing Set screw type Shaft 1) Unit number Nominal dimensions Bolt Bearing number dia. size mm mm inch. mm inch inch H L J A N N 1 H 1 H 2 L 1 B S N1 N B S A H 2 H 1 L1 H J L. 63 UCP2 NTN P203D1 S(SM)-UCP201D1 C(CM)-UCP201D1 5 8 51 67 62 0.7 0.7 1.0

Plummer Blocks ( Bearing housings ) Plummer Block SN-524 and above are Series SN 500 for bearings with adapter sleeves. supplied with eye bolt on cap mm inch L H A B E V S Ca N N1 SN 518 80 --- 145 100 345 100 290 35 20 62 27 22 1218 K + H 218 16.2/160 2 FS 330 2218 K + H 318 11.2/160 2 22218CK + H 318 11.2/160 2

Plummer Blocks ( Bearing housings ) Plummer Block SN-524 and above are Series SN 500 for bearings with adapter sleeves. supplied with eye bolt on cap mm inch L H A B E V S Ca N N1

Plummer Blocks ( Bearing housings ). Series SN 500 for bearings with adapter sleeves. Plummer. Blocks. DesignAtion. Shaft. Dia d1. DIMENSION IN MM. Bearing 

SKF SNH plummer block housings Bearing types • Self-aligning ball bearings • Spherical roller bearings Bearing dimension series • 02, 03, 22, 23, 32 Shaft diameter range • 25 – 160 mm Typical shaft-bearing combination • Plain shaft with bearing on an adapter

UCP 200 & UCP 300 - Plummer block housing units Cast iron housing, radial insert ball bearing with grub screws in inner ring. d mm HL J A N N 1 1 H 0 S B Q UCP 201 12 30,2 127 95 36 13 19 14 60,0 12,7 31 M6 M10 UC 201 P ,65 UCP 202 15 33,3 127 95 36 13 19 14 60,0 12,7 31,0 M6 M10 UC 202 P ,65

Plummer Block Housings. Flat Bottom Type SN5F, SN6F Series for Bearing with Adapter Sleeve. Shaft Diameter : 20 ~ 60mm. 20. 1N=0.102kgf.

11 Cap & Fixing Bolts Sizes Recommended Tightening Torques SNN Housing Cap Bolt Size Grade 8.8 Recommended max. Tightening Torque Base Bolts Size Grade 8.8 Recommended Nm Nm SNN505 M10 50 M12 80 SNN506-605 M10 50 M12 80 SNN507

6 HFB · Wälzlager - Gehäusetechnik · Buchen technica lchanges reserved 03/05 SNI- and SN - Plummer Block Housings are split bearing housin gs for the fitting of self aligning ball or spherical roller be arings which are fixed to the shaft either by shrink fitting