usg shaft wall assembly

Typical Shaft. Wall Assembly. Utility Chase. USG C-H Stud. 1”SHEETROCK Brand gypsum liner. or enhanced gypsum liner panels. USG J-Runner.

Title: E:NER-258SW_2HrCorridorCeilingAndStairSoffit NER-258 SYSTEM G (1) Author: EWatanabe Created Date: 9/5/ 9:55:15 AM

8/19 · The assemblies listed below are a small sample of the UL Designs in which USG shaft wall systems can be used. For more details on fi re-rated assemblies, see USG literature SA926, Shaft Wall Systems. SSA926S_08.indd 3A926S_08.indd 3 99/13/07 1:33:52

SCAFCO has engineered and designed the I-Stud Shaftwall Fire ratings, installation instructions, and CAD detail assemblies available at SCAFCO.com.

Division 090000 - Finishes. 092910 Gypsum Board Shaft Wall Assemblies. USG Corporation. 550 West Adams Street Chicago, IL 60661 USA. Contact:

Shaftwall systems are nonload-bearing fire rated wall assemblies that provide The CH System is produced under license and control of USG Corporation.

CGC Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are finished later, along with interior partitions. Installation is quick and easy, using components and application procedures familiar to drywall contractors.

Title: USG Fire Resistant Assemblies Wall Penetration Details (English) - J2133 Keywords; null Created Date: 10/16/ 6:36:15 AM

45 USG-040903 Based on 4 C-H studs 25 gauge 51 RAL-OT04-018 Based on 4 C-H studs with 3 mineral fi ber insulation The assemblies listed below are a small sample of the UL Designs in which USG shaft wall systems can be used. For more details on fi re-rated assemblies, see USG literature SA926, Shaft Wall Systems.

1/29 · Three different ways to get one job done using USG Sheetrock® Brand products.

USG. Cavity Shaft Walls are non-load bearing gypsum board partition assemblies designed for erection from outside the shaft at each floor.

Shaftwall. One layer 1″ x 24″ (25.4 mm) ToughRock® Shaftliner or DensGlass® Shaftliner panel inserted between 2-1/2″ floor and ceiling runners of 2-1/2″ steel C-T, C-H studs. Opposite side: Base layer of 5/8″ (15.9 mm) ToughRock® Fireguard X® Products or 2/8″ (15.9 mm) DensArmor Plus® Fireguard® gypsum panels installed

The Cavity Shaft Wall System includes components that provide the strength to withstand lateral loads and fire protection necessary for walls that enclose elevator shafts, stairwells and other

USG Shaftwall E Stud, Used to construct elevator shafts, mechanical shafts, stair shafts, services risers, air return shafts and horizontal shaft wall 

4 USG Shaft Wall Systems Overview USG shaft wall systems are non-loadbearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and the walls are finished later, along with interior

Three-Hour Cavity Stair Wall (Non-Load Bearing), See Figure 5 4. 1-in thick SHEETROCK® Brand Gypsum Liner Panel - Friction-fitted in "H" portion of C-H studs. Two-Hour Horizontal Stud Shaft Wall Assembly (Non-Load Bearing), See Figure 6 1. A minimum 4-in deep 20 gauge J-runner to be installed vertically, on the ends of the wall.

USG Drywall Suspension System Stucco/Plaster/EIFS is designed specifically for interior and exterior stucco, plaster or EIFS applications. Featuring the USG-patented, Quick- Release™ Cross Tee Clip, the system offers a faster install compared to traditional framing methods. Furthermore, new tees were developed to match the dimensions of the

Provide the strength to withstand lateral loads and fire protection necessary for walls that enclose elevator shafts, stairwells and other vertical shafts.

United States Gypsum Company USG, Gypsum Board Shaft Wall Systems. CSI 3-Part Specifications., identical with those of applicable assemblies tested per.

11/1 · How can I achieve a higher STC shaft assembly? Insulate the wall, use resilient channels or sound isolation clips, and/or install Gold Bond® BRAND SoundBreak® XP® as one of the face layers. Here are a few UL 2-hour rated designs that achieve an STC of 50 or higher: U497, STC 52 (Sound Test: NGC2017007), U498, STC 53 (Sound Test: NGC2015036).

STEEL BEAM WITH FIREPROOFING REFERENCE STRUCTURAL DRAWINGS. FOR BEAM SIZE AND FIREPROOFING THICKNESS. USG SHEETROCK © BRAND SHAFT LINER GYPSUM PANELS, CUT TOP