torque specs for brake rotors

Front and rear brake torque specs. Jump to Latest Follow 1 - 2 of 2 Posts 2006. Only show this user. Would someone please verify the caliper to caliper bracket and bracket to hubs torque specs. for the front and rear please. Rotor-to-hub bolts ----- 94 ft-lb Disc brake caliper anchor bolts ----- (a)

Turning brake rotors is a term that is used to describe machining, or lathing, brake rotors down to remove the excess brake material from your pads and to prevent warping and grinding, thus extending the life of your brake pads. Turning a rotor allows for smooth braking action and creates less heat then those that are warped.

Front & rear brake disc's have different torque, if their front, instructions should be right. Front brake rotors - 16-24 ft lbs. Rear braske 

i think it's like 7 or 17 ft/lb just hand tight on the rotor screws pyromaster's Avatar. pyromaster , 08-23-2002 11:53 AM.

2007. 6. 13. · Torque Specs for front Brakes. Jump to Latest Follow 1 - 12 of 12 Posts well, so far i have used original factory rotors and pads. i believe in doing it right the first time. weather permitting this weekend I'll use the proper loc tite and torque it to the right specs. thanks again for all your support.

I reached out to my contact at Kodiak regarding the Disc Brake Kit # K2R1058D11E and he said the rotor/spacer bolts need to be torqued down 

2012. 6. 12. · Brake rotor to hub 16 Nm (12 ft-lb) Front brake pad carrier to steering knuckle 110 Nm (81 ft-lb) That was very helpful. Oddly, for the rear brake the info seems to be missing or possibly incorrect. Torque spec for front brake caliper main bolts is 110NM. TIS does not list rear caliper bolt torque for E39.

AzntaggeR said: so i've searched on here and even googled it and can't seem to find the exact answer. i'm replacing the front rotors and i basically need to know what the torque specs are for the front 6mm rotor bolts that screw to the wheel. thanks in advance. You need a service manual. They are available through getting a Red R or you can

The following table lists general torque specifications for common brands and components. Contact the manufacturer for updated torque specifications. We will keep this chart updated

2011. 3. 4. · My Harley dealer tell me to torque at 120 lbs for the primary cover, and that's o.k But i don't know if it was in ft or inch. Primary cover torque is rated in inch lbs- 108-120 inch lbs.

This means that removal and installation is also the same. The brake caliper gets torqued down to 22 ft-lbs and the brake bracket gets tightened to 56 ft-lbs.

Front brake rotor to hub - 12 ft/lbs - make sure you put anti-seize on threads and just snug it down. The lug bolts hold the rotor on the hub.

Front rotors:-nominal thickness - 1.140"-discard thickness - 1.080" Source: MOTOR Brake specifications guide, Note - There has been conflicting torque specs for the rear caliper bracket bolts. GMSI and Motor show 148ft lbs, while a Helms book shows 89ft/lbs. At the time of this edit, the official answer is unknown.

The importance of the correct tightening torque of the wheels is often overlooked, especially when performing tyre replacements. A poorly secured wheel, as far as the correct tightening of nuts and bolts is concerned, has a lot to do with the irritating vibrations on your steering wheel when you brake and with the general malfunctioning of your braking system.

are activated, to compensate for rotor and brake pad wear and to keep the running clearance constant. During pad or rotor maintenance, the technician manually sets the system's initial non-braked position. The total running clearance (the sum of clearances on both sides of the rotor) should be between 0.024 to 0.043 in. (0.6 to 1.2 mm).

I picked up an Enforcer front wheel for my bike. I'm installing Arlen Ness rotors on it. The torque spec for my 09 stock wheel is 16 to 

SRAM Torque Specifications. Buyer's Guide. Bike Torque Wrenches: The Best For 2021. Choosing the right torque is important, Shift-brake lever (mechanical brakes) - clamp bolt: 8.0: 70: Rotor bolts: 6.2: 55: Front flat mount caliper - mounting bolts (all) 5.0: 44: Rear caliper -mounting bolts (all) 5.0: 44: Calipers banjo bolt: 5.0

Gary. There are guide pins for the calipers, caliper adapter bolts and the lug nuts. Lug nuts are 110 ft-lbs. Front Caliper Guide Pins 44 ft-lbs. Front Adapter Bolts 70 ft-lbs. Rear Caliper Guide Pins 23 ft-lbs. Rear Adapter Bolts 85 ft-lbs.

Note: Gen II - FRONT Brake Hose to Caliper Banjo Bolt 295 lb-ft of torque @ 3,000-4,500 rpm frequently asked torque specs SOURCE: Need the correct torque specs for 2004 silverado 1500 calipers Tighten the 2 brake caliper mounting bolts to 108 Nm (80 ft i downshifted and coasted to a stop, then got a tow home i downshifted and coasted to a stop, then got a tow home.

And the rear rotor torques to the same spec. The rotors on the pre 06 400 front and rear also torque to 16.5 lb ft and I would suspect the 07+ 

How to Change the front brakes · Edge Front Brake Caliper Torque Specs : 30 ft-lbs · Edge Front Brake Bracket Torque Specs : 75 ft-lbs