clinker cooler

Typical clinker cooler products include the QuikTurn 60PC for casting applications and the QuikTurn 60G for gunning areas such as the tertiary air duct outlet. For the most severe abrasion, select the R-Max PC QT or the R-Max G QT. For further cement questions or assistance, contact Resco Products. RELATED PRODUCTS Alumex P-85-HS PDS SDS

Cooling Air Quantity is maintained to ensure cooling of clinker and heat recuperation from hot clinker from kiln. Specific air usage is generally considered as key performance indicator of cooler. New generation coolers can cool clinker to the temperatures to as low as 65 0C over ambient with a specific air consumption of 1.7 kg/kg-clinker.

Clinker Flow Direction 12 13 Typical ETA cooler results: Optimum recuperation High secondary and tertiary air temperature High middle air for WHR or drying purposes Cold clinker at the end of the cooler Clinker Flow Direction ETA Cooler = Thermal homogenisation Static Inlet HEModule

High-quality water in the office is key to a better, more productive work life. The clean, refreshing water from a Culligan water cooler boosts morale from the break room to the board room. With a space-saving design that takes up less than one square foot, your water cooler fits perfectly into most any setting and requires minimal maintenance.

The clinker temperature is the main constraint for the measurement. With the SICKBulksckan product, it’s possible to control the clinker flow thickness independently of the gas

Rotary cooler is also called clinker cooler, which is the important support equipment of cement rotary kiln. It is mainly used to cool the high-temperature clinker（1000-1200℃）discharged from the rotary kiln into an appropriate temperature (less than 200℃). The cold air produced by it contact countercurrent with the clinker in the

10/29 · Gas cooling Clinker cooler Clinker cooler System-optimizing, -protecting and efficiency-enhancing cooling. Following capacity increases, cooling with air alone is often no longer sufficient to achieve the proper operating conditions of the downstream filter. Injecting water into the clinker cooler provides a remedy here.

Clinker Cooler. After cement is dried by being put through a rotary kiln and converted to clinker, it needs to be cooled. Cooling tunnels are used to reduce 

The clinker cooler, also known as grate cooler or cement cooler, it is a necessary equipment of cement clinker production. The clinker cooler is mainly used to cool and transport the cement

After 50 years of experience with conventional grate coolers Claudius Peters developed a modern and future-oriented machine to overcome all disadvantages of 

Clinker level in the cooling system. Level measurement at cement clinker cooler. The clinker is cooled as it is discharged from the rotary kiln onto 

Uses: The grate cooler is an important main equipment in the clinker burning system of the cement plant. Its main function is to cool and transport the cement clinker. At the same time, it provides hot air for the rotary kiln and the decomposition furnace, which is the heat recovery of the firing system. The main equipment.

To produce cement, the raw meal is burned to clinker in a long rotary kiln. After leaving the rotary kiln, the clinker has a temperature of up to +1300 °C and must be cooled down to a temperature of about +200 °C for further storage. To achieve this, the clinker bed is cooled with a continuous stream of air.

AGICO supplies grate coolers for cement clinker production. The clinker coolers we offer are the most advanced reciprocating grate coolers, which are widely 

Clinker cooler. Monitoring the cooling air flow. Application. Monitoring the cooling air flow · Temperature monitoring at bearings. Application.

7/10 · the development of clinker coolers in recent times has been guided by market demands for maximised availability, reduced maintenance and rapid conversion with minimum production downtime, accompanied by the over-arching requirements to reduce energy consumption and minimise the impact on the environment. thyssenkrupp has responded to

Clinker enters from one end and is lifted and scattered by flights. At the same time, the cold air enters from the other end and contacts with the clinker countercurrent for heat exchange. The rotary cooler is generally arranged under the rotary kiln, with a diameter of 2-5m and a length of 20-50m. Grate cooler Grate cooler is a quench type cooler.

As shown in Fig. 1, high temperature clinker get into grate cooler from rotary kiln. Clinker layermoves slowly on grate bed. Cooling air blows into the clinker layer vertically from the bottom ofthe clinker, permeates and diuses in the clinker to cool the red-hot clinker. Cooling air becomeshot air after exchanging heat energy with clinker.

The clinker discharged from the rotary kiln enters the rotary cooler and is rapidly quenched with water from 1,400°C to 600°C. White cement cooler.

Clinker coolers in today's cement pyroprocessing lines are considered to be very reliable even under kiln upset conditions. But what is the interaction of 

Waste air of (grate) clinker coolers is the cooling air that is in excess of the combustion air and is blown to ambient (via dedusting system). The only purpose of this air is to further cool down the clinker. (Please see also definitions in section precalciners) 7 Holcim Group Support fCooler Recuperation Efficiency cooler = Q loss