For example, -4 size would normally designate a 1/4” ID but in this case, the actual ID is 3/16”. Because fittings are sized to fit the hose ID, the 26 series fitting sizes for the hose end of the fitting are not the actual measurements but nominal size –
Learn MoreGaugeable Tube Fittings and Adapter Fittings, Available in tube sizes from 1/16 to 2 in. and 2 to 50 mm, Consistent gaugeability upon initial installation, Easy to disconnect and retighten, Wide variety of materials and configurations, Demonstrated reliability and performance www.swagelok.com, 2 Tube Fittings, TUBE FITTINGS, Features,
Learn MoreThe standards used to check Dimensions of Pipe Fittings For Wrought Product (WP) Dimension is covered in ASME B16.9- which is standard for Factory-made Wrought Butt-welding ASME B16.9- which is standard for Factory-made Wrought Butt-welding Fittings for size NPS 1⁄₂ to NPS 48" and ASME B16.28-
Learn MoreBrowse Victaulic pipe fittings, adapters & outlets in stainless steel, copper, HDPE, PVC/CPVC & more materials. Various size & pressure ranges available Accommodating pipe pressure ranging from 0 to 4000 PSI/276 Bar and pipe sizes of from ¼" to 60"/ DN20 to DN1500 Victaulic's pipe fitting products can meet the requirements of
Learn MoreSUITABLE TU MATERIALS. S-LOK Single Ferrule Tube Fittings can be used with the following tube specifications. Stainless steel tube;.
Learn Morestainless steel Schedule 10S in Sizes thru 12" and to Schedule 10 in sizes 14" and larger. 2. Standard Wall thicknesses are identical tostainless steel Schedule 40S in sizes thru 12". 3. Extra Strong Wall thicknesses are indentical to stainless steel Schedule 80S in sizes thru 12". 4. May be of welded pipe, x-rayed and stress-relieved. 5.
Learn MorePipe Fittings Dimensions ASME150 / 300 & DIN2484. CRP produce pipe fittings to international standards. ASME B16.5 which is widely adopted in the US and UK, and DIN2848 which is used by most of Europe. The guides we have produced assist our customers in their lined piping plant designs. We recommend that either one of these standards should be used.
Learn MoreThe tube dimensions define the difference between tube and pipe, with wall thickness of pipe being greater than that of tube for the same outside diameter. Also tube products are defined by their outside diameter measurement, while pipe is measured by the nominal inside diameter (ie Nominal Bore, NB) and the Schedule (wall thicknesses).
Learn MoreNot recommended for use with Swagelok tube fittings in gas service . Ordering Information, Dimensions, and Pressure Ratings Example: Type 316 stainless steel 1/2 in . OD × 0 .035 in . wall at 1000°F 1 . The allowable working pressure at -20 to 100°F (-28 to 37°C) is 2600 psig (Fractional Sizes, page 3) . 2 .
Learn MoreFor Swagelok-brand instrument tube fittings 1 inch in size and smaller, the general procedure to "swage" a new connector to a tube is to tighten the nut 1-1/4 turns past finger-tight. Insufficient turning of the nut will fail to properly compress the ferrule around the tube, and excessive turning will over-compress the ferrule, resulting in leakage.
Learn MoreParker Tube Fittings General Material Specifications · Standard Material Specifications Chart for Seal-Lok, Triple-Lok, Ferulok, Intru-Lok, Pipe, Port Adapters,
Learn MoreIt covers dimensions for pipeline flanges, valves, pipe fittings, etc. GOST Flanges. SAE Dimension Standards. Society for Automotive Engineers, abbreviated as SAE is an American organization, developing technical standards for various types of flanges, pipe and tube fittings, valves and high strength fasteners for automotive industry.
Learn MoreThis standard specifies dimensions for stud ends and tapped holes with metric fine pitch thread and pipe thread for use with compression fittings, valves and
Learn MorePVC Pipe Sizes & Dimensions Guide (Charts) When it comes to the PVC pipes themselves, there are 3 key metrics: Outer diameter, inside diameter and wall diameter (as in wall thickness). Below are a series of PVC pipe diagrams and dimension charts to help you find the right sizes (or at least get you informed as to the various common sizes
Learn MoreI-Line Fitting Dimensions I-Line Fittings can be measured by different locations on the fitting in order to determine size. As you can see with the line drawing for a Male I-Line Ferrule below, you can measure the following locations to determine the size of your fitting. Outside Diameter of Flange Outside Diameter of Tube End
Learn MoreShop in stock stainless steel compression tube fittings male connectors and cryogenic service with dimensions and specifications listed.
Learn MoreIn another example, a -10 tube would indicate a tube with an outside diameter of 10/16", or 5/8". Fittings are a little different and slightly more complex. In the part number 10343-8-6, for example, -8 is the size of the fitting end connection, and -6 is the hose size.
Learn MoreHtf Stainless Steel Tube Connector 316 and 304, Size/Dimension: 6mm To 25.4 Mm Fill the quantity to get latest price! Number, piece, Other.
Learn MoreUltra-High-Vacuum Flanges andFittings for Stainless Steel Tubing. Create access points in ultra-high-vacuum lines or chambers by bolting two same-size flanges together with a copper gasket between them. The flanges' sharp edges dig into the copper gasket and form an extremely tight seal, which means they handle higher vacuum pressures than
Learn MoreTube O.D. 1/8" 3/16" 1/4" 5/16" 3/8" 1/2" 5/8" 3/4" 7/8" 1" 1-1/4" 1-1/2" 2". Thread Size-B 5/16-24 3/8-24 7/16-20 1/2-20 9/16-18 3/4-16 7/8-14 1-1/16-12 1-3/16-12 1-5/16-12 1-5/8-12 1-7/8-12 2-1/2-12. EATON Weatherhead Hose Assembly Master Catalog W-HYOV-MC002-E3 February 2011.
Learn MoreTo complement this extensive range of fittings, we supply AISI 316/304 stainless steel tube in sizes from ½ inch to 4 inch (exterior dimensions). Stocked in 6m random lengths, the tube comes with polished or bright unannealed finishes.
Learn More